2080400

Receipt paper empty

1. Replenish receipt paper2. Check the status of sensor and its connector

2080500

Receipt paper setting error

1. Check the status of setting paper2. Check the status of sensor and its connector

2080600

Command is received while doing self-test

1. After terminating self-test and initialize receipt printer

2080700

No receipt paper

1. Replenish receipt paper in paper charger2. Check the status of sensor and its connector

2080800

Receipt paper cutting error

1. Check the Cutter module2. Check if printer head lever is properly close

2080900

No sensing black mark (dark sensor)

1. Check the status of Black mark sensor2. Check if Dip switch # 6 is correctly set (Dip switch # 6 is set by On in case of not using Black mark)

2131500

CS4 sensor detects note in delivery path before CDU dispenses Sensor is located along the delivery path right before the reject bin.

Remove note from the CDU delivery path.

3000000

To shows that received command was undefined

3000100

To show command parameter error

3000200

The reception of the command that impossible to implementation

3000400

To show that error data was included in command

3000500

To show that a command, which requires the card movement, was executed before IC contacts were released from the card

3001000

To show that the card was not carried to the specific location after specified number of trial for specified time during execution of command of carrying card in various ways

3001100

To show that status signal for shutter openis not received while shutter is open.

3001200

To show that the Sensor is damaged or more that one card is inside ICRW.

3001300

To show that the card longer than 92mm is inserted into ICRW

3001400

To show that the card shorter than 78mm is inserted into ICRW

3001500

To show that data in F-ROM is damaged

3001600

To show that the card staying inside ICRW was moved up to the point where status request information change. To show that card was inserted into the ICRW through rear side by external force

3001700

To show that the card was not carried to the specific location after specified number of trial for specified time during execution of RETRIEVE command.

3001800

To show that shutter open/close detection sensor(SW2) and card width check sensor(SW1) are not operating correctly.

3001900

To show that a card was not inserted from the rear, even if 10 seconds had passed after the execution of BACK ENTRY command

3002000

To show that track has parity error

3002100

To show that read error has happened in Multiple magnetic read command.

3002200

To show that write error is detected through write/verify procedure.

3002300

To show that only SS,ES,LRC are contained in the track. (no retry)

3002400

To show that the card has no magnetic track(no retry)

3002500

To show that quality error(Jitter,Preamble,Postamble) has happended in write verify.

3002600

To show that the track has no SS.

3002700

To show that the track has no ES

3002800

To show that the track has no LRC error

3002900

To show that the discordance of write data has happened in write verify.

3003000

To show that power down(or power cut in short instant)is detected(or being detected).

3003100

To show that DSR signal was turned to OFF(communication is cut)

3004000

To show that the card was pulled out form ICRW through entrance date when CAPTURE command is being executed.

3004100

Failure at IC Contact solenoid or sensor ICD.

3004300

Card could not be set to IC contack position/Failure at sensor PDI.

3004500

ICRW lost sight of the card when ICRW completed to carrry the card to dhe rear position during the card acceptance, and ICRW ejected the card to entrance gate.

3004600

To show that the ejected card has not been withdrawn during execution of Monitoring for removal command.

3005000

Retract counter overflow.

3005100

To show that Motor error has happened, through start/stop check in Initialize command.

3005300

To show that read error in Digital Decode Read Command.

3006000

To show that there found abnormal condition on the power-line.

3006100

The receiving error for ATR.

3006200

To show that the specified protocol does not agree with that of ICC/SAM ICRW still connected.

3006300

In case T=1 cards, after ATR receiving, IFS exchange is failed. ICRW detects time out.

3006400

In case T=1 cards, after ATR receiving, IFS exchange is failed. ICRW detects protocol error.

3006500

HOST tried to communicate with IC card without card activation.

3006600

ICRW tried to activate with ICC/SAM, but the card returned ATR, which is not supported.

3006900

ICRW tried to activate with ICC/SAM, but the card returned ATR, Which does not match EMV.